OSHA 1910.30   Training  Requirements – Important things to know 1/2

OSHA 1910.30 Training Requirements – Important things to know 1/2


This section adds training requirements to 29 CFR 1910, subpart D, requiring training on fall and equipment hazards, as well as the requirement for retraining, if necessary.

1910.30(a)(2)   The employer must ensure that each employee is trained by a qualified person, not a competent person, and not just be treated as a casual, “put this on and use it” command!

  1. A qualified person is defined by OSHA as one who, “by possession of a recognized degree, certificate, or professional standing, or who by extensive knowledge, training, and experience, has successfully demonstrated their ability to solve or resolve problems relating to the subject matter, the work, or the project”.

  2. According to 1910.140(d)A competent person is capable of identifying existing and predictable hazards in any personal fall protection system or component, as well as in their application and uses with related equipment. They also have the authority to take prompt corrective actions to eliminate the identified hazards.

Provided by Ken Kempa

OSHA 1910.30   Training  Requirements – Important things to know 1/2

OSHA 1910.29 Fall Protection Systems & Falling Object Protection- Criteria and Practices – 5/5 – Important things to know


PROTECTION FROM FALLING OBJECTS:

1910.29(k) – the employer must ensure workers are protected from falling objects (1910.28(c) also relevant)

OSHA defines falling object protections as the need to ensure:

  1. Toeboards used for falling object protection are:
    • Of sufficient length where erected, along the exposed edge of the overhead walking-working surface, to protect employees below.
    • Have a minimum height above the surface of 3.5 inches, with a gap of no more than 0.25-inch.
    • Capable of withstanding without failure, a force of at least 50 lbs. applied, in either any downward or outward direction, at any point along the toeboard.
  2. Paneling or Screening considerations if materials are piled higher than the toeboard:
    • To be installed from the toeboard to the midrail of the guardrail system.
    • Also installed to the top rail, if items are piled higher than the midrail.
    • Must have openings small enough to prevent objects from falling through the opening.
  3. Canopies if used for protection below: employers must ensure canopies used for falling object protection, are strong enough to prevent collapse or penetration by falling objects.
  4. Barricading Area Below into which objects could fall, prohibiting workers from entering the barricaded area, and keeping objects far enough away from the edge to help prevent them from falling to a lower level.
  5. Equipment Tethers or Lanyards: though not specified in the ruling, a beneficial proactive measure is to tether or use lanyards on tools or equipment, to prevent them from falling to a lower level.

Provided by Ken Kempa

OSHA 1910.30   Training  Requirements – Important things to know 1/2

OSHA 1910.29 Fall Protection Systems & Falling Object Protection- Criteria and Practices – 4/5 – Important things to know


ADDER SAFETY SYSTEMS:

1910.29(i) – establishes the criteria/practices, for ladder safety systems permanently attached to fixed ladders, or immediately adjacent to ladders.

  1. Workers must be able to climb up or down with both hands free for climbing. And the system does not require them to continually hold, pull or push any part of the system while climbing.
  2. The employer must ensure that the connection, between the system and the attachment point to the body harness or belt, does not exceed 9-inches in length, in order to limit the length of any fall.
  3. Employers must ensure that the ladder safety systems and their supports, are capable of withstanding without failure, a drop test of 500 pounds for a distance of 18-inches, without hitting a lower level.

Provided by Ken Kempa

OSHA 1910.30   Training  Requirements – Important things to know 1/2

OSHA 1910.29 Fall Protection Systems & Falling Object Protection- Criteria and Practices – 3/5 – Important things to know


HANDRAIL and STAIR RAIL SYSTEMS:

1910.29(f) – this section establishes the criteria/practices for handrail and stair rail systems, addressing height, finger clearances, surfaces, stair rail opening, handholds, projection hazards, and strength.

  1. Handrails must be not less than 30-inches, and not more than 38-inches high, if there are 4 or more risers.
  2. Requires there is a finger clearance of at least 2.25-inches between handrails and any other object (such as a wall).
  3. Stair rail systems must be at least 30-inches high, if installed before January 17, 2017, or no less than 42-inches high if installed after that date.
  4. No opening in a stair rail system can exceed 19-inches in its least dimension.
  5. Employers must ensure that handrails and top rails of stair rail systems, are capable of withstanding without failure, a force of at least 200 pounds applied in any downward or outward direction, within 2-inches of any point along the top edge of the rail.

Provided by Ken Kempa

OSHA 1910.30   Training  Requirements – Important things to know 1/2

OSHA 1910.29 Fall Protection Systems & Falling Object Protection- Criteria and Practices – 2/5 – Important things to know


DESIGNATED AREAS- WARNING LINES:

1910.29(d) – this section establishes the criteria and practices for “Designated Areas,” which in the final rule in 1910.21(b), defines as “a distinct portion of a walking-working surface delineated by a warning line, in which employees may perform work without additional fall protection.”

A DESIGNATED AREA WARNING LINE- must meet all these requirements:

  1. Is a rope, tape, wire, or chain, warning employees they’re approaching an unprotected edge or side.
  2. Has a minimum breaking strength of 200 lbs.
  3. Is clearly visible from a distance of 25-feet, and anywhere within the designated area.
  4. Needs to be erected as close to the work area as possible, while still allowing the task to be performed.
  5. Be installed so that its lowest point, including sag, is not less than 34-inches and not more than 39-inches above the walking-working surface.
  6. Be supported so that pulling on one section of the line between supports, will not result in slack being taken up from other sections, resulting in the first section line pushing/falling to below 34-inches.

Provided by Ken Kempa

OSHA 1910.30   Training  Requirements – Important things to know 1/2

OSHA 1910.29 Fall Protection Systems & Falling Object Protection- Criteria and Practices – 1/5 – Important things to know


GUARDRAIL SYSTEMS:

1910.29(b) – states the specific requirements for the minimum and maximum height of guardrail systems.

  1. For guardrails, the General Industry regulations are now aligned with the Construction rules.  The requirement for the top rail is 42-inches, plus or minus 3-inches.  Additionally, the new rule states that openings between top and midrail can be no greater than 19-inches.
  2. The rails must be capable of withstanding a force of at least 200 lbs. applied in a downward or outward direction within 2-inches of any point along the top edge of the rail.  At this loading, the top rail may not deflect to a height of less than 39-inches above the walking-working surface.
  3. Midrails, screens, mesh, intermediate vertical members (no more than 19-inches apart), solid panels or other equivalent members, must be capable of withstanding without failure, a force of at least 150 lbs. in any downward or outward direction, and any point along the intermediate member.
  4. Also prohibits the use of steel or plastic banding for top rails or midrails in guardrail systems, due to the potential of sharp edges. However, steel or synthetic rope is permitted.

Provided by Ken Kempa